BMW 330D E90 Rail pressure sensor linearization

Posts related to specific vehicles, or any other general tuning info.

Return to General tuning

BMW 330D E90 Rail pressure sensor linearization

Postby jbirschner » Fri Jun 24, 2016 12:21 pm

Hi All,

Could somebody please help me or advise about how BMW ecu works to read rail pressure from rail pressure sensor?

My BMW 330D E90 have a BOSCH 0281002497 sensor rated at 1800 bar but accordingly to other specs that I found on internet from other bosch 1800 bar sensor that it can read up to 2100 bar.

My car is set up at 1970 bar rail and it is working fine except logs only show max 1835 bar.
My Stock Sensor map was:
0v = 0bar
0.5v = 0bar
4.5v = 1800bar
5v = 1800bar
now I changed it to:
0v=0bar
0.5v=0bar
4.5v = 2000bar
5v = 2000bar

So now I can see now full pressure up to 1970 bar defined on my map. Is my above map for 2000bar correct?

I also tried to install a 2200 bar sensor BOSCH 0281006064 and changed the map to:
0v=0bar
0.5v=0bar
4.5v=2200bar
5v=2200bar

But my idle was terrible and engine was shaking, rpm was going up and down and I read 0.90v signal going to ecu and old sensor shows 0.97v so I tried many times and gave up. New sensor is RDS 4 and old is RDS 2?? I don't know if it affects anything.

So could you please confirm if my 2000 sensor map is correct set and also why my new 2200 bar sensor didn't' work and why? Is it because that different sensor type RDS 4 and RDS 2?

Thank you so much if you could help me.

Regards,
Jackson.

jbirschner
New user
 
Posts: 5
Joined: Fri Jun 24, 2016 11:58 am
Location: London

Re: BMW 330D E90 Rail pressure sensor linearization

Postby jocasfe » Fri Jun 24, 2016 2:02 pm

Hi m8, very good question...
Please upload your file, I think you dont find the right map, or it mas be changed in more then ones...

jocasfe
New user
 
Posts: 7
Joined: Sun Jun 19, 2016 12:17 am
Location: Portugal

Re: BMW 330D E90 Rail pressure sensor linearization

Postby A.Dutsov » Wed Mar 01, 2017 11:36 am

you can try 0 300 3000 3300 0 0 2000 2010 as its in edc17 lin, also i think the 2010 can be 2200 without problem ...

A.Dutsov
New user
 
Posts: 14
Joined: Sat Apr 13, 2013 1:34 pm
Location: България

Re: BMW 330D E90 Rail pressure sensor linearization

Postby nutron » Tue Dec 11, 2018 5:11 pm

Contrary to popular belief, the voltage range of all Bosch high pressure sensors are not the same. I know at least one of those but probably both have different voltage ranges.

nutron
New user
 
Posts: 9
Joined: Mon Feb 04, 2013 9:32 pm
Location: South

Re: BMW 330D E90 Rail pressure sensor linearization

Postby toni6542 » Mon Dec 16, 2019 2:33 pm

You use stock sensor for 2000bar?

toni6542
New user
 
Posts: 19
Joined: Tue Apr 02, 2019 8:30 am
Location: Serbia

Re: BMW 330D E90 Rail pressure sensor linearization

Postby cap » Tue Sep 28, 2021 3:39 pm

1800Bar e90 stock sensor will read to about 1840Bar, then it simply stops outputting more voltage.

cap
New user
 
Posts: 1
Joined: Tue Sep 28, 2021 3:38 pm
Location: portugal


Return to General tuning

Who is online

Users browsing this forum: No registered users and 3 guests