Siemens SID and Galleto 1260

Software used for ECU editing

Return to ECU Tuning Software

Siemens SID and Galleto 1260

Postby tomik1987 » Sun May 19, 2013 1:33 pm

Self cable and soft Galleto 1260, to today, I met only with EDC15C2 bosch ones can do just fine. But today I had a Siemens SID 801 Galleto load your controller but when I wanted to download a file. thrown error. Can you help? advice?
You do not have permissions to view the files yet. You have to be registered and you have to make at least 3 quality / unique posts.

tomik1987
Bronze
 
Posts: 40
Joined: Mon Apr 01, 2013 3:10 pm
Location: Slovak Republik

Re: Siemens SID and Galleto 1260

Postby julianstefanov » Sun May 19, 2013 1:50 pm

This is not a error. It's a normal message which you must follow to read the ECU.
You must enter the ECU in BOOT Mode, then you can read it with galletto.

User avatar
julianstefanov
Bronze
 
Posts: 28
Joined: Sun Feb 24, 2013 12:44 pm
Location: Bulgaria

Re: Siemens SID and Galleto 1260

Postby tomik1987 » Sun May 19, 2013 2:22 pm

how exactly do I enter in ECU boot mode? I do it in the program? Galleto 1260??

tomik1987
Bronze
 
Posts: 40
Joined: Mon Apr 01, 2013 3:10 pm
Location: Slovak Republik

Re: Siemens SID and Galleto 1260

Postby julianstefanov » Sun May 19, 2013 4:29 pm

You must do the following:

1. Open the ECU (be carefull)
2. Find the EEPROM 29F400 inside (it's on the picture)
3. Solder a cable on pin 28 (like on the picture)
4. Put that cable to your car GND (gnd on the battery)
5. Put your key on position 2 (ignition on) - DO NOT start the engine!!!
6. Connect Galletto to the OBDII port and read the ECU
7. Disconnect Galletto
8. Disconnect the cable from 28 pin and remove it totaly
9. Close the ECU
10. DONE

Now you'll have the EEPROM DUMP and you can edit/modify and then WRITE BACK to the ECU as many times as you want without any cables or opening the ECU. Just 1st time when you have to read the EEPROM, you must use the steps from 1 to 10.

If something is not clear, let me know.

Regards
Julian
You do not have permissions to view the files yet. You have to be registered and you have to make at least 3 quality / unique posts.

User avatar
julianstefanov
Bronze
 
Posts: 28
Joined: Sun Feb 24, 2013 12:44 pm
Location: Bulgaria

Re: Siemens SID and Galleto 1260

Postby ominimicu » Wed May 22, 2013 5:31 pm

are u sure galletto will read that????

ominimicu
Bronze
 
Posts: 26
Joined: Wed May 22, 2013 4:44 pm
Location: Spain for now

Re: Siemens SID and Galleto 1260

Postby julianstefanov » Sun Jun 02, 2013 7:22 pm

Ofc I'm 1000% sure. :)

User avatar
julianstefanov
Bronze
 
Posts: 28
Joined: Sun Feb 24, 2013 12:44 pm
Location: Bulgaria

Re: Siemens SID and Galleto 1260

Postby BrunoC » Wed Sep 11, 2013 12:15 am

siemens sid 806 run the same way, ie connecting the pin 28 to mass?
the pin is the next picture?

http://youyoukiller.free.fr/boot_mode/p ... 06%201.jpg

is it safe?

Thank you for everything.

BrunoC
New user
 
Posts: 6
Joined: Sun Sep 08, 2013 12:28 am
Location: Portugal

Re: Siemens SID and Galleto 1260

Postby Rocknsock » Mon Apr 13, 2015 9:35 pm

I need that information too, about sid 806!

Rocknsock
Bronze
 
Posts: 34
Joined: Wed Nov 19, 2014 4:54 am
Location: Lisbon

Re: Siemens SID and Galleto 1260

Postby mo_ferwana » Tue Apr 14, 2015 10:30 am

ominimicu wrote:are u sure galletto will read that????

Hi
Yes I am sure it can

mo_ferwana
New user
 
Posts: 3
Joined: Tue Apr 14, 2015 9:54 am
Location: Palestine Gaza

Re: Siemens SID and Galleto 1260

Postby Rocknsock » Tue Apr 14, 2015 12:18 pm

julianstefanov wrote:You must do the following:

1. Open the ECU (be carefull)
2. Find the EEPROM 29F400 inside (it's on the picture)
3. Solder a cable on pin 28 (like on the picture)
4. Put that cable to your car GND (gnd on the battery)
5. Put your key on position 2 (ignition on) - DO NOT start the engine!!!
6. Connect Galletto to the OBDII port and read the ECU
7. Disconnect Galletto
8. Disconnect the cable from 28 pin and remove it totaly
9. Close the ECU
10. DONE

Now you'll have the EEPROM DUMP and you can edit/modify and then WRITE BACK to the ECU as many times as you want without any cables or opening the ECU. Just 1st time when you have to read the EEPROM, you must use the steps from 1 to 10.

If something is not clear, let me know.

Regards
Julian

Does it work also for SID 806?

Thanks

Rocknsock
Bronze
 
Posts: 34
Joined: Wed Nov 19, 2014 4:54 am
Location: Lisbon


Return to ECU Tuning Software

Who is online

Users browsing this forum: No registered users and 0 guests