Siemens PDD 1.2 DPF off

by **kowalwalcz** » Mon Aug 04, 2014 6:46 pm

Please remove the DPF filter from this file. Ecusafe or volta work not correctly
Touran 170HP 2007 2.0TDI

http://www74.zippyshare.com/v/74221323/file.html

thanks for All

by **samir00** » Wed Aug 06, 2014 9:15 am

03G906018EH1.rar

after flashing connect vcds and do a regeneration of dpf

Prerequisites (General):
Ignition ON
Engine ON (Idle)
Coolant Temperature above 50 °C (see MVB 002.4)
Particle Filter Load below Specification (see MVB 075.3, VAG-COM should give the specified value)
If the Particle Filter Load is above Specification the Particle Filter needs to be replaced since the car may burn down when regenerating.
Power Consumers ON (Light, Seat Heating, Front/Rear Window Heater, Climate Control)
Conditions (Driving Cycle):
Vehicle Speed between 30-60 km/h (18-37 MPH)
Engine Speed between 1500-2500 RPM (4th or 5th Gear, Automatic Transmission in Tiptronic)
Duration approx. 15-20 Minutes
Exhaust Gas Temperature before Turbo Charger above 700 °C
Drive the car based on the above conditions until the Particle Filter Load is as low as possible (close to 0 %). In case the regeneration fails there can either be problems with the Driving Cycle Conditions or with the Engine Hardware.

[Select]
[01 - Engine]
[Coding-II - 11]
Enable Regeneration by Entering 21295.
[Do It!]
[Meas. Blocks - 08]
Select both Groups at once 070 and 075.
[Go!]
MVB 075.3: Particle Filter Load needs to be 0.0
after that disconnect the dpf sensors.

by **kowalwalcz** » Thu Aug 07, 2014 7:19 pm

thanks samir00

I test it and post result

;)

by **easylifeauto** » Mon Aug 18, 2014 7:03 pm

Hi i have same prolem.
Seat leon read via bdm and dpf off "volta" .
car smoke straight away.

by **zani70** » Tue Aug 19, 2014 12:33 pm

samir00 wrote:
03G906018EH1.rar

after flashing connect vcds and do a regeneration of dpf

Prerequisites (General):
Ignition ON
Engine ON (Idle)
Coolant Temperature above 50 °C (see MVB 002.4)
Particle Filter Load below Specification (see MVB 075.3, VAG-COM should give the specified value)
If the Particle Filter Load is above Specification the Particle Filter needs to be replaced since the car may burn down when regenerating.
Power Consumers ON (Light, Seat Heating, Front/Rear Window Heater, Climate Control)
Conditions (Driving Cycle):
Vehicle Speed between 30-60 km/h (18-37 MPH)
Engine Speed between 1500-2500 RPM (4th or 5th Gear, Automatic Transmission in Tiptronic)
Duration approx. 15-20 Minutes
Not good. Deleted the entire table with the errori.EGR still active.
Exhaust Gas Temperature before Turbo Charger above 700 °C
Drive the car based on the above conditions until the Particle Filter Load is as low as possible (close to 0 %). In case the regeneration fails there can either be problems with the Driving Cycle Conditions or with the Engine Hardware.

[Select]
[01 - Engine]
[Coding-II - 11]
Enable Regeneration by Entering 21295.
[Do It!]
[Meas. Blocks - 08]
Select both Groups at once 070 and 075.
[Go!]
MVB 075.3: Particle Filter Load needs to be 0.0
after that disconnect the dpf sensors.

by **zani70** » Tue Aug 19, 2014 12:35 pm

Not good. Deleted the entire table with the errori.EGR still active.

by **samir00** » Tue Aug 19, 2014 12:48 pm

This is only dpf, egr not remowed.
I tested it and it worked with no errors.

by **zani70** » Tue Aug 19, 2014 4:15 pm

You can not have errors, why and removed entire table DTC. The real problem is that if you have another problem you have no signal.
I do not know if you understand, because my English is very bad .This way of removing dpf is not professional and would not recommend to anyone.