throttle error after flashing ori

Posts relating to recovering blocked ECUs

Return to Recovering ECU

throttle error after flashing ori

Postby murfieus » Wed Dec 06, 2017 4:56 am

hi guys, hope someone can help me with this
my mk5 golf gti 2.0tfsi dsg med9.1 gives an throttle error after i wrote the ori file back and doesnt responce on the gaspedal. i tryed an tuned file with a other letter at the end.

ori 1k0907115A and tuned 1k0907115J.

i did a ori fullread and checksums were OK. then i fullwrote the tuned file and it gives some shocks at full load but it drives ok with part throttle so i did a throttle bassicsettings and an adaption but still the same issue.
so i fullwrote the ori back and now it wont responce and have a bad idle. i tryed the bassicsettings and adoptions but still no luck.
it has a dtc in the throttle and it says error when i try the basicsettings. its acting like i have put a wrong ecu in it but i only changed the files.

i use mppsv18 to read and write.

thnks!

murfieus
New user
 
Posts: 5
Joined: Wed Dec 06, 2017 3:42 am
Location: netherlands

Re: throttle error after flashing ori

Postby sandor1987 » Wed Dec 06, 2017 6:04 pm

if you really know something about tuning you should know that you cant flash other software into your ecu special med9 and med17 easy to brick... its not a edc15 or me7...

** Dutch **
in je voorstel topic gaf je aan al wat te weten over het tunen enzo.
maar betwijfel het... anders had je allang geweten dat je NOOIT andere software erin kunt pompen...
het is geen edc15 of me7 die niet te bricken zijn.
je speelt nu gewoon met vuur en je mag geluk spreken dat je uberhaupt nog kan rijden en daarbij het schokken is al niet goed.
beter zeker zijn van je zaak want het zou zonde zijn als je blok aan stront loopt

sandor1987
Diamond
 
Posts: 295
Joined: Sun Sep 08, 2013 5:21 pm
Location: Netherlands

Re: throttle error after flashing ori

Postby eivin96 » Fri Dec 08, 2017 11:48 am

That’s checksum error, did you wrote the file with mpps?

Your problem is nothing special or unusual, but you need VCP to recover it.

Or simply write the backup file in bdm mode with ktag

eivin96
Bronze
 
Posts: 31
Joined: Mon Nov 14, 2016 1:27 pm
Location: Germany

Re: throttle error after flashing ori

Postby murfieus » Sun Dec 10, 2017 5:46 pm

hi , yes i writed it with mpps and brought the ecu to a friend of mine with bdm en writed a full backup and it runs propperly again :)

murfieus
New user
 
Posts: 5
Joined: Wed Dec 06, 2017 3:42 am
Location: netherlands

Re: throttle error after flashing ori

Postby eivin96 » Thu Dec 21, 2017 1:08 pm

That’s a common problem with clone hardware...

eivin96
Bronze
 
Posts: 31
Joined: Mon Nov 14, 2016 1:27 pm
Location: Germany

Re: throttle error after flashing ori

Postby Sven77 » Sun Aug 15, 2021 1:39 am

Ive had this a few times,

I managed to fix the problem by saving (0) in adaptation channel 0 then cycle the ignition and do basic settings 060.

Sven77
New user
 
Posts: 10
Joined: Mon Dec 10, 2012 1:26 am
Location: South Africa


Return to Recovering ECU

Who is online

Users browsing this forum: No registered users and 0 guests