It is currently Fri Mar 29, 2024 8:49 am

News News of Map Factors, Offsets, Units and Calculations

Site map of Map Factors, Offsets, Units and Calculations » Forum : Map Factors, Offsets, Units and Calculations

Questions and answers related to map factors, units, offsets. How to...

edc15c2 checksum help

Hi, could someone help me by calculating the checksum for this file? thanks
Read more : edc15c2 checksum help | Views : 125 | Replies : 3


Newbie question about some maps inside EDC17C08 - 1.6CRDI

Hello,

As the title stated, I`m one 100% "newbie" on the field of messing with car software. Also,wish to point out that I do not work as tuner or similar related profession! Neither consider it..
The cars are just hobby. Totally away from my profession.. and the one I wish to mess a bit is mine own KIA 1.6 CRDI - 128HP/260Nm
Bought already one file with maps description, but it was for a bit ...
Read more : Newbie question about some maps inside EDC17C08 - 1.6CRDI | Views : 220 | Replies : 0


EDC15C7 OPEL 1.7CDTI Map Sensor Scale 2.5Bar to 3 Bar

Hi, I am trying to scale my map sensor from 2.5bar to 3Bar with winols.

Anyone knows the Address and what values should I change to?

Regards!
Read more : EDC15C7 OPEL 1.7CDTI Map Sensor Scale 2.5Bar to 3 Bar | Views : 529 | Replies : 1


Question about Fuel Restore?

Hello guys, i found the fuel restore address. So if im deceleration in the area, where im set fuel restore (example 0-5000rpm) which fuel and injection maps im using at deceleration?
I got also ignition timing idle map. (is only 3x8 big, rpm from 480 to 3080 and load(ms) 2,3,4)
I have for LOW Part and HIGH Part fuel 10maps (5low,5high) and for ignition timing 6maps (3 low, 3high).
Read more : Question about Fuel Restore? | Views : 524 | Replies : 0


WinOLS Bosch MED17 offset

Hi all,

For some context I am learning to map my own car which is a Fiesta ST180. I've pulled the map off the ECU and have got hold of a DAMOS file from a local tuning company. They did state the offset will likely need setting, but should be ok otherwise. I have spent some time looking over the DAMOS finding the things I need to change, but now I'm trying to make changes ...
Read more : WinOLS Bosch MED17 offset | Views : 843 | Replies : 3


Help required please..Lifting Mitsubishi SH7058 Torque Limi

Good Morning

Please could someone help me lift torque limit on my maps

512Nm is what it tops out on and I'm eventually needing 600-1000 Nm on my build.

Is it done by factor as I know these.

Is there a limit switch?
L200 F969L ORI READ.rar
Read more : Help required please..Lifting Mitsubishi SH7058 Torque Limi | Views : 344 | Replies : 0


SID206 (1.8 TDCI) offsets and factors

Hi, i didn't find a mappack for my ecu so i'm trying to create it myself.
I made logs and thanks to this I am trying to determine factors and offsets.
The first problem is that I have a strange AFR (from the smoke map).
I believe that such values of 1:25 are impossible.
AFR.png
Read more : SID206 (1.8 TDCI) offsets and factors | Views : 286 | Replies : 0


BMW Factor/Offset for Driver Wish EDC16C31

Hello, can you help me?
Cant find the right factor/offset for the driver wish map.
it's about values -350Nm...

BMW e46 320d 2002year
sw: 1037361858

https://i.imgfly.me/jWVuvy.md.png
Read more : BMW Factor/Offset for Driver Wish EDC16C31 | Views : 556 | Replies : 1


HFM2 to HFM5 conversion on Audi 1.8T with M3.8.2 ECU

Hey tuning-folks,

I have a couple of questions considering an HFM 2 to HFM 5 conversion on my Audi A4 B5 with a 1.8T (AEB) with an M3.8.2 ECU (0261204805). The car is running a K04-15 upgrade turbocharger and is maxing out the orignal HFM and injectors.

First step therefore is to get an HFM running, which can read more airmass than the original one. I already made an adapter harness for an HFM5 from ...
Read more : HFM2 to HFM5 conversion on Audi 1.8T with M3.8.2 ECU | Views : 854 | Replies : 2


Factor/Offset for siemens ems2000

Can anyone help me? Cant find the right factor/offset for the load and boost table.

I found all the adresses.

Car volvo v40 t4 2001
ecu EMS2000

I need to know the offset for the TCV/boost duty cycle
And the load table.

Attached stock bin file.
Read more : Factor/Offset for siemens ems2000 | Views : 458 | Replies : 0


 

Login  •  Register


Statistics

Total posts 79427 • Total topics 26506 • Total members 33552